All content on EnviroDIY is licensed as Creative Commons Attribution-ShareAlike 4.0. Hardware designs on EnviroDIY are released under the CERN Open Hardware License 1.2. Alternative licenses are available. Learn more
Welcome to EnviroDIY, a community for do-it-yourself environmental science and monitoring. EnviroDIY is part of WikiWatershed, an initiative of Stroud Water Research Center designed to help people advance knowledge and stewardship of fresh water. New to EnviroDIY? Start here
Community Activity See all activity
Shannon Hicks replied to the topic Error Compiling for board EnviroDIY Mayfly 1284p in the forum Mayfly Data Logger 1 months ago
The unzipped folders go into your MyDocumenrs/Arduino/libraries folder. Make sure they aren’t nested within a second ‘libraries’ folder within the first one. What version of the IDE are you using?
A good way to check that your libraries are installed correctly is to look at the built-in examples. In the ARduino IDE, go to the File dropdown me…[Read more]
JK_WCCD replied to the topic Error Compiling for board EnviroDIY Mayfly 1284p in the forum Mayfly Data Logger 1 months ago
Yes, I believe I have. It looks like I downloaded all recommended EnviroDIY libraries (47). Do I need to do anything with them once I have them in my library folder? Do I need to install all of them in Arduino somehow?
Shannon Hicks replied to the topic Error Compiling for board EnviroDIY Mayfly 1284p in the forum Mayfly Data Logger 1 months ago
Have you installed all the supporting libraries into your Arduino/libraries folder? There should be either 32 folders worth of libraries, or 47, depending on whether you downloaded all the recommended EnviroDIY libraries, or just the ModularSensors dependencies.
JK_WCCD started the topic Error Compiling for board EnviroDIY Mayfly 1284p in the forum Mayfly Data Logger 1 months ago
Hello,
I am trying to upload the sketch through the following instructions (ModularSensors/examples/DRWI_NoCellular at master · EnviroDIY/ModularSensors · GitHub)
I followed all the directions but when I try to verify or upload the sketch through Arduino onto our Mayfly, I get the following error message –
<p style=”text-align: center;”>exit s…[Read more]
JK_WCCD became a registered member 1 months ago
JK_WCCD
@jkimpawccd
Shannon Hicks replied to the topic Reading -9999 on all Sensors in the forum Mayfly Data Logger 1 months ago
Have you tried measuring the voltage being applied to the sensors by using a voltmeter when the channel scanning sketch is running? For the turbidity sensor’s screw terminal board, put the voltmeter’s red probe on either of the V+ screws, and the black probe on either of the GND screws. For the CTD sensor’s 3.5mm headphone jack adapter board p…[Read more]
WFUWater replied to the topic Reading -9999 on all Sensors in the forum Mayfly Data Logger 1 months, 1 weeks ago
Hello, we’ve returned to try and set up the two sensors again but are still running into the issues of both being vacant at every location. We have tried both of them individually and have changed the 3.3v position to the 12v position for the Clarivue sensor. The Hydros is still connected to the 3.3v. We have also changed the sketch for the…[Read more]
neilh20 replied to the topic Artifactual troughs and flickers in recorded stream depth in the forum Monitor My Watershed 1 months, 1 weeks ago
@d_manning just wondering if you have had any insights 🙂
Rachel Frantz became a registered member 1 months, 1 weeks ago
Rachel Frantz
@rfrantz
Shannon Hicks replied to the topic Reading -9999 on all Sensors in the forum Mayfly Data Logger 1 months, 1 weeks ago
In your 4th picture, it looks like the Grove cable plug may not fully be seated in the grove jack. Not sure about any of the other ones since the angles in the photos didn’t show them well, but be sure that it’s pressed all the way into the jack. And your second photo shows that your two SDI12 Grove jack voltage selection jumpers are both set t…[Read more]