All content on EnviroDIY is licensed as Creative Commons Attribution-ShareAlike 4.0. Hardware designs on EnviroDIY are released under the CERN Open Hardware License 1.2. Alternative licenses are available. Learn more
Welcome to EnviroDIY, a community for do-it-yourself environmental science and monitoring. EnviroDIY is part of WikiWatershed, an initiative of Stroud Water Research Center designed to help people advance knowledge and stewardship of fresh water. New to EnviroDIY? Start here
Community Activity See all activity
Khaase replied to the topic Mayfly 1.1 Bootloader Burning? in the forum Mayfly Data Logger 1 years, 11 months ago
That is useful, and along the lines of my thinking: moving to LiSOCL2. Though I am having trouble getting supplies to test. The internal impedance of those, especially when low or cold, is a big question. My system can use all the deep-sleep tricks, but when measuring the load spikes up to ~350 mA for fractions of a second, and I wonder if this…[Read more]
Dave replied to the topic depth sensors for water wells in the forum Environmental Sensors 1 years, 11 months ago
Hi Karl
Have you had a look at maxbotix? Not sure if they do a 150m ranging sensor – could you mount the sensor on a rod and insert that to say 140m or is the fluctuation in level too much?
https://www.maxbotix.com/
This video also presents a range of options, more on the diy side…
Dave
neilh20 replied to the topic Mayfly 1.1 Bootloader Burning? in the forum Mayfly Data Logger 1 years, 11 months ago
Maybe of interest https://www.envirodiy.org/topic/primary-powering-in-cold-settings/
Khaase started the topic Mayfly 1.1 Bootloader Burning? in the forum Mayfly Data Logger 1 years, 12 months ago
I haven’t seen a discussion about burning a bootloader to the Mayfly 1v1. I presume the best way to so go through J7 with my ISP.
Is there any special guidance? How is this done during assembly?
The reason I am messing with the bootloader is that I’m trying to get Mayflys to live off some big batteries for a project in a cold dark place for a…[Read more]
Khaase became a registered member 1 years, 12 months ago
Khaase
@khaase
Adolfo Lopez started the topic PlatformIO Developer Setup in the forum Mayfly Data Logger 1 years, 12 months ago
Hello all,
I’ve been trying to properly set up my platformio.ini configuration file to test some code out, but keep running into issues. I tried following the steps from the ModularSensors page but haven’t had any luck. Would someone be able to walk me through this process?
SPY replied to the topic Serial1 of MayFly could not communicate in the forum Other Data Loggers 2 years ago
Dear Shannon , I have already connected the GND of the Modem and GND of the Mayfly. Interfacing between Mega2560 to the Modem I have used of level converter ( 3.3V to 5 V) for TX1 and RX1 . Because the operating of the modem is 3.3 Volt and the the Mega is a 5 Volt.
The operating of the Modem was a 3.3 Volt for the RX1 and TX1 and operating the…[Read more]
dan@wachusett replied to the topic 2022 EnviroDIY Hardware Status and Availability in the forum Mayfly Data Logger 2 years ago
Is there any updated timeline on the RS-485 half shield production? The last update was about 6 months ago.
Thanks!
Adolfo Lopez became a registered member 2 years ago
Adolfo Lopez
@alopezmi
Shannon Hicks replied to the topic Alternative to Amazon in the forum Mayfly Data Logger 2 years ago
No, the only official way to buy a single Mayfly is through our listing in Amazon, while 5-packs can be purchased through the Shop on this website.