Activity – EnviroDIY

jbiddle replied to the topic Editing Variable UUIDs in the forum Monitor My Watershed 4 years, 8 months ago

I totally understand. I’m thankful that I’m still able to work full time from home it has been incredibly challenging. But I totally get it and it it’s totally understandable. Thanks again for taking the time to help me with this.

The lib_dep part of the platform.ini…[Read more]

Sara Damiano replied 4 years, 8 months ago

Correct. Or you can just add a semi-colon in front of the “ModularSensors” line and remove the semi colon from the link’s line.
- jbiddle replied 4 years, 8 months ago
  
  Thank you. Once I do that, do I need to do anything to update the board?
  - Sara Damiano replied 4 years, 8 months ago
    
    You should be able to just reprogram it with the same program. If that errors, let me know.
    - jbiddle replied 4 years, 8 months ago
      
      Thanks Sara. This is the monitor output in testing mode now:
      
      ——————————————
      Current logger time is 2020-05-11T10:47:22-05:00
      ———————–
      CampbellOBS3 at ADS1115_0x48_Channel0 reports turbidity is 1.13185 nephelometricTurbidityUnit
      CampbellOBS3 at ADS1115_0x48_Channel1 reports turbidity is 1.02158…[Read more]

Sara Damiano replied to the topic Editing Variable UUIDs in the forum Monitor My Watershed 4 years, 8 months ago

I’m sorry. I finally fixed pushed what I think should be the changes needed to the develop branch, but I still haven’t programmed an actual board to test it.

This everyone being home all the time situation is brutal. Anyone doing well with it is clearly a lot more disciplined and organized than I am.

jbiddle replied to the topic Editing Variable UUIDs in the forum Monitor My Watershed 4 years, 8 months ago

Hello Sara, sorry to bother you but I wanted to check in again about this.

Is there something I could do in the meantime while you work on the testing mode update? Is there a way I can try to fix the connection issue without using the testing mode? Thanks.

Sara Damiano replied to the topic Bringing in serial data through UART on 20-Pin connector in the forum Mayfly Data Logger 4 years, 8 months ago

I’m just seconding what Shannon said about using the hardware UART – always use hardware UART unless you definitely cannot. In your case where you’ll be parsing long NMEA sentences, I’d recommend actually re-wiring your Bee/modem to give your GPS the better connection if you’re trying to use both. In your code, you just use “Serial1” to c…[Read more]

Shannon Hicks replied to the topic Bringing in serial data through UART on 20-Pin connector in the forum Mayfly Data Logger 4 years, 8 months ago

Are you sure you need to use UART 0 for your incoming data from your deice? The RX0/TX0 pins on the 20-pin header are directly wired to the main UART 0 of the Mayfly, which are the same pins that are used when programming the Mayfly board via your computer (using either the USB port of the FTDI header). So if you have a device connected to R…[Read more]

Kurt Rosenberger started the topic Bringing in serial data through UART on 20-Pin connector in the forum Mayfly Data Logger 4 years, 8 months ago

Hello

I’m just getting started with the Mayfly, and am trying to bring in met data from an Airmar PB-100, using a GPS sketch I found for the Arduino (it is formatted as NMEA-0183, as they were built for boats). But my first hurdle is to even get the data in. I have an RS-422-TTL converter to bring the data in on the UART (I know this thing works…[Read more]

jbiddle replied to the topic Editing Variable UUIDs in the forum Monitor My Watershed 4 years, 8 months ago

No apology necessary, it had been a little while so I just wanted to check in and see if there had been any progress. Thank you for the update.

Sara Damiano replied to the topic Editing Variable UUIDs in the forum Monitor My Watershed 4 years, 8 months ago

I’m so sorry. I haven’t tested it yet.