Welcome to EnviroDIY, a community for do-it-yourself environmental science and monitoring. EnviroDIY is part of 
@dartmouthwsn
Active 4 years, 1 months ago-
David Lutz replied to the topic Increasing resolution and reading differential voltage in the forum Mayfly Data Logger 6 years, 7 months ago
Iris,
I’d be interested to hear what you find. Here in NH we have interest in sap flow measurements for projects in conjunction with the Proctor Maple Syrup Institute at UVM. Installing Mayfly-based networks could be really interesting to them.
Dave
-
David Lutz replied to the topic HCSR04 & Sw5 in the forum Mayfly Data Logger 6 years, 7 months ago
The Grove connectors are currently a bit of a pain to procure. They are available on SeeedStudio and Amazon but my sense is that everything is back ordered. I’ve had to have them shipped from Hong Kong over the past few months.
-
David Lutz replied to the topic Low power project in the forum Mayfly Data Logger 6 years, 7 months ago
I wanted to resurrect this particular thread because we have been running into the same issue that Chan had. However, I note that there is a new variant of the SDI12 library as of roughly 2 weeks ago (EnviroDIY_SDI12_PCINT3) and I am pretty sure that it is an updated version of the SDI12_mod that Shannon sent in response a few years back in this…[Read more]
-
David Lutz replied to the topic Mayfly v 0.4 or 0.5? in the forum Mayfly Data Logger 6 years, 8 months ago
Hi Beth,
Yes of course! Just checked – we have 0.5b. Don’t know how I overlooked that!
Another quick question that you may/may not know – if you are connecting an external 12v power supply to the mayfly, what type of jack is needed to connect the power source to the Mayfly? Is that just a male JST jack? (pictured here: jack)
Thanks!!
-
David Lutz started the topic Mayfly v 0.4 or 0.5? in the forum Mayfly Data Logger 6 years, 8 months ago
Dear EnviroDIY,
I’m working on setting up a sensor network with a variety of soil moisture and temp/rh sensors. We’re using a CS-215 to handle temp/RH and it requires 12VDC. The trick is that we obtained our Mayfly via a colleague at another institution and aren’t sure if the board is 0.5 or 0.4. Obviously if it is 0.5 it can handle the 12V…[Read more]
-
David Lutz posted a new activity comment 7 years, 2 months ago
Hi there Neil,
Well right now we’re quite focused on a handful of important characteristics of forest ecosystems, predominantly air T, soil T, plant available moisture, and volumetric soil moisture. The general paradigm shift we see now is that single sensor nodes do not provide the spatial or temporal resolution for us to understand microclimate…[Read more]
-
David Lutz posted a new activity comment 7 years, 2 months ago
I’m working on constructing wireless sensor networks with the Forest Service and a handful of Research Universities across New England for use in forested ecosystems (soil, temp, humidity, irradiance, etc). Although I’m an ecosystem scientist and not an electrical engineer, there is a growing need to get portable low-cost sensors out for…[Read more]
-
Hi Dave
Great to hear about it – this is a board to bring together the ecosystem sciences and software/electronic to make it happen.
Be great to hear how you are going about defining and refining the sensor networks.
I’ve been designing remote instream water sensors. The challenges has been low cost environmental protection, solar powering, field…[Read more]-
Hi there Neil,
Well right now we’re quite focused on a handful of important characteristics of forest ecosystems, predominantly air T, soil T, plant available moisture, and volumetric soil moisture. The general paradigm shift we see now is that single sensor nodes do not provide the spatial or temporal resolution for us to understand microclimate…[Read more]
-
For a leafy canopy 2.4Ghz gets absorbed by the water. 900Mhz gives a much range in a leafy canopy for lower power. The WiFi standard is evolving to include a “low data rate” in sub 1GHz – but no time lines for which silicon will have it first.
I’d be interested in what you find with specific sensors – it can be painful – however calibration and…[Read more]
-
-
-
-
David Lutz became a registered member 7 years, 2 months ago
For a leafy canopy 2.4Ghz gets absorbed by the water. 900Mhz gives a much range in a leafy canopy for lower power. The WiFi standard is evolving to include a “low data rate” in sub 1GHz – but no time lines for which silicon will have it first.
I’d be interested in what you find with specific sensors – it can be painful – however calibration and…[Read more]